GuidesClicking
Why Is My Furnace Clicking? Each Pattern, and Which Ones Need a Technician
Last updated: November 16, 2026 · Published by Colton Air Conditioning, NV license 0092120
Short answer: A few clicks when the heat starts, and a few more when it shuts off, are usually the furnace's own controls and metal parts doing their job. Clicking that repeats with no flame, clicking that comes with the heat starting and stopping over and over, or a rapid chatter from the cabinet while it runs is not normal. Switch the system off at the thermostat. Then have a licensed technician look at it. The igniter, flame sensor and gas valve are gas-side parts, so leave the cabinet closed. Smell gas or hear a hiss? Leave the house right away. Don't use light switches, thermostats, appliance controls or anything that could spark. Once you're outside, call 911 and Southwest Gas (877-860-6020). See furnace smells like gas.
Match the click to the moment
| When you hear it | What it usually is | Normal? |
|---|---|---|
| One or two clicks as the heat is called, then a hum and a whoosh | The control board relay, the draft motor and pressure switch, then the burners lighting | Yes |
| Rapid ticking at the burners, but no flame | A spark igniter firing while gas never lights | No |
| Clicks, a short run, silence, then the same clicks again | The furnace starting and stopping on a safety | No |
| Light ticking from vents or walls while warm air flows | Metal ductwork expanding as it heats | Usually |
| A buzz-click chatter from the cabinet mid-cycle | A relay on the control board, or a switch opening and closing | No |
| A click or two after the burners stop, then ticking as things cool | The gas valve closing, the blower relay, ducts contracting | Yes |
Normal start-up clicks
On a typical gas furnace, a call for heat runs the same steps every time. A relay on the control board clicks. The draft motor starts, and a pressure switch closes once the venting is drawing, often with a small click of its own. The igniter either glows silently or sparks with a ticking sound. The gas valve opens with a soft click, the burners light, and after a short delay the blower starts. If warm air follows, those clicks are normal.
Clicking with no flame
This is the pattern behind "furnace clicking but not turning on." The sequence starts but never finishes. On a spark-ignition furnace, you may hear steady ticking at the burners while no flame appears. On a furnace with a hot-surface igniter, you may hear the relay and pressure switch click, wait, then try again before the furnace locks out. Likely causes, each one a technician's job:
- Igniter. A worn or cracked igniter can't light the gas.
- Gas valve. The igniter works, but the valve never opens or opens weakly.
- Flame sensor. The burners light for a moment, the sensor doesn't prove flame, and the control shuts the gas off.
Older systems may have a standing pilot instead. See our furnace pilot light guide for that setup. For a furnace that does nothing at all, start with furnace not turning on.
Clicking on and off
If the furnace clicks, runs for a short stretch, goes quiet, and repeats, it is short cycling. Each restart repeats the relay and valve clicks, so the sound is a symptom, not the problem. The usual triggers are a limit switch opening because the heat exchanger is running too hot, a pressure switch dropping out because the venting isn't proving, or a flame sensor losing the flame signal mid-cycle. Each one is the furnace protecting itself. Switch the system off at the thermostat. Then book a visit rather than letting it keep retrying.
Clicking or ticking while running
Light ticking from the vents, walls or ceiling while warm air is flowing is usually sheet-metal ductwork expanding as it heats. It settles once the ducts warm up. A sharper buzz or rapid click from inside the furnace cabinet is different. A relay on the control board that chatters, or a limit or pressure switch opening and closing during the cycle, can sound like that. If the clicking comes from the furnace itself rather than the ducts, have it checked.
Clicking after shutoff
When the burners stop, the gas valve closes with a click. The blower keeps running briefly to pull heat off the heat exchanger, then its relay clicks off. Ducts and the heat exchanger tick as they cool. All of that is normal. Clicking that keeps repeating long after the cycle ends, or a relay that clicks with no heat call, points to the control board and is worth a visit.
Why Las Vegas homes notice it more in winter
NOAA's 1991–2020 normals for Harry Reid International Airport put the average December low at 39.6°F and the January low at 40.5°F. The National Weather Service notes that the airport often reads 5 to 15 degrees warmer at night than outlying parts of the valley. The coldest readings usually come on the lower east side or the higher west side. Furnaces in those colder parts of the valley are more likely to be running on a cold night, so a new click gets noticed sooner.
FAQ
Why is my heater clicking but not turning on?
The furnace is starting its ignition sequence but not finishing it. The igniter, gas valve or flame sensor is the usual cause. Switch the system off at the thermostat. Then have a licensed technician check it.
Is a clicking furnace dangerous?
Normal start-up and shutoff clicks are not. Repeated clicking with no flame means gas-side parts aren't working as designed. Switch the system off at the thermostat. Then have it inspected.
Why does my furnace click after it shuts off?
The gas valve closes, the blower relay clicks off, and the ducts tick as they cool. Repeated clicking long after the cycle ends can point to the control board.
Call (702) 738-6976 to schedule.
Services
Furnace Repair Las Vegas
Furnace repair for Las Vegas homes when the desert night finally drops and the heat will not stay on.
Heating Repair
Gas furnace repair for Las Vegas homes, plus heat pumps, with the safety checks a gas system needs.
Emergency Heating Repair
No-heat calls in Las Vegas. Furnaces and heat pumps diagnosed before replacement talk.
